Radiographer Jobs - Qassim Saudi

Mechanical Maintenance and Repair Activities Perform planned preventive, predictive, corrective, and breakdown maintenance activities on assigned mechanical equipment Carry out daily inspections, running checks, and maintenance checklists in accordance with approved maintenance schedules Monitor the physical condition of equipment and report abnormalities, non-conformances, and developing defects to the Mechanical Maintenance Engineer Troubleshoot mechanical failures using approved tools, drawings, manuals, and diagnostic techniques to identify the cause and carry out necessary repairs Perform dismantling, inspection, cleaning, repair, replacement, reassembly, alignment, and functional testing of mechanical equipment and components Replace defective parts such as bearings, seals, gaskets, O-rings, gland packing, couplings, bolts, filters, strainers, belts, and lubrication-system components Perform adjustment, alignment, tightening, lubrication, greasing, oil top-up, oil changing, and cleaning activities in accordance with approved procedures Identify and report corrosion, cracks, leaks, overheating, vibration, abnormal noise, misalignment, loose bolts, damaged insulation, and other equipment defects Ensure the working area is clean, safe, and properly restored after completion of maintenance activities<br><br>v Support maintenance, inspection, and repair of mechanical equipment including, but not limited to:<br><br>Siemens 9000HL-Class gas turbine auxiliaries, including lube oil, hydraulic oil, fuel gas, inlet air, ventilation, and turning gear systems Steam turbine auxiliaries, including lube oil, gland steam, seal oil, condensate, cooling, and turning gear systems Heat Recovery Steam Generator (HRSG), including drums, valves, blowdown systems, expansion joints, and associated auxiliary equipment Pumps, including boiler feedwater pumps, condensate extraction pumps, closed cooling water pumps, service water pumps, fire water pumps, fuel oil pumps, chemical dosing pumps, and drainage pumps Compressors, blowers, fans, air handling units, ventilation fans, and instrument/service air compressor systems Valves, including gate, globe, check, control, safety Valves Water treatment, reverse osmosis, condensate polishing, chemical dosing, wastewater treatment, and other balance-of-plant mechanical equipment Inspection, Testing, and Troubleshooting Conduct routine inspections and condition assessments of assigned mechanical equipment Use approved maintenance and diagnostic tools such as vibration meters, infrared thermometers, laser alignment tools, dial gauges, feeler gauges, torque wrenches, pressure gauges, vernier calipers, and micrometers Assist in vibration monitoring, alignment checks, bearing inspections, pump performance checks, valve testing, pressure testing, leak testing, and functional testing Record inspection findings, test readings, equipment condition, defects identified, and maintenance work completed Assist in identifying the root cause of equipment failures and support implementation of corrective actions Monitor repeated failures and report recommendations for repair, modification, replacement, or maintenance-plan improvement Support basic welding, fabrication, and workshop repair activities Participate in planned shutdowns, major outages, overhauls, commissioning activities, warranty works, and emergency repairs Safety, Permit-to-Work, and Compliance Follow all applicable safety rules, permit-to-work requirements, lockout/tagout procedures, confined-space-entry requirements, lifting procedures, and site safety standards Verify that equipment is properly isolated, depressurized, drained, vented, cooled down, and released for maintenance before starting work Use required personal protective equipment, approved tools, lifting equipment, and safety devices at all times Participate in toolbox talks, risk assessments, safety observations, hazard reporting, audits, and incident investigations Immediately report unsafe conditions, leaks, damaged tools, lifting hazards, near misses, and incidents Follow environmental and waste-management requirements, including proper identification, handling, segregation, and disposal of waste materials Ensure maintenance work complies with approved site procedures, OEM requirements, quality standards, and EHS requirements Documentation and CMMS Support Complete maintenance checklists, inspection sheets, work completion records, test reports, and defect reports accurately Provide clear feedback to the Mechanical Maintenance Engineer regarding work completed, materials used, defects found, and follow-up actions required Support work-order completion, man-hour recording, and equipment-history updates in the CMMS Spare Parts, Tools, and Housekeeping Review assigned work orders and identify the required spare parts, consumables, tools, lifting equipment, and test instruments before starting work Check availability of spare parts and coordinate with the warehouse storekeeper for material collection and return Maintain mechanical hand tools, power tools, lifting tools, portable test instruments, and workshop equipment in good working condition Report shortages of spare parts, consumables, special tools, and defective equipment to the Mechanical Maintenance Engineer Maintain good housekeeping in workshops, equipment areas, stores, and maintenance locations Coordination, Training, and Continuous Improvement Work closely with Mechanical Maintenance Engineers, Operations personnel, Electrical and I&C teams, contractors, OEM representatives, and other site personnel Support Operations during equipment isolation, release for maintenance, testing, start-up, and return-to-service activities Assist other departments in troubleshooting and repair activities when required Support training and mentoring of junior technicians,, and newly joined maintenance personnel<br><br>Participate in continuous-improvement initiatives, maintenance improvement programs, 5S activities, and hazard-reporting programs.<br><br>Requirements<br><br>Education<br><br>Mechanical Diploma, Mechanical Technology, or an equivalent discipline Mechanical trade certifications is preferred Training in rigging, lifting operations, Forklift operator, and safety courses is an advantage<br><br>Experience<br><br>Minimum 5 years of mechanical maintenance experience in a power plant, heavy industrial facility, oil and gas plant, desalination plant, petrochemical plant. Combined cycle power plant experience is preferred<br><br>Technical Knowledge<br><br>Knowledge of mechanical systems used in combined cycle power plants Knowledge of gas turbines, steam turbines, HRSG systems, pumps, valves, compressors, fans, blowers, heat exchangers, filters, strainers, and piping systems Understanding of lube oil, hydraulic oil, fuel gas, fuel oil, cooling water, condensate, boiler feedwater, compressed air, and water-treatment systems Knowledge of rotating-equipment maintenance practices, including bearing inspection, lubrication, seal replacement, coupling alignment, and vibration awareness Familiarity with valve maintenance, including gland packing, seat leakage, Lapping, and basic valve overhaul activities Understanding of lifting and rigging, torque tightening, mechanical assembly, and use of lifting tools Knowledge of permit-to-work, lockout/tagout, confined-space entry, lifting operations, and general mechanical safety requirements<br><br>Practical Skills<br><br>Ability to use maintenance diagnostic tools such as vibration meters, infrared thermometers, pressure gauges, and tachometers Basic computer skills for CMMS andwork-order updates, maintenance records, and reporting Good working knowledge of written and spoken English Good communication, teamwork, and coordination skills Willingness to work during planned outages, emergency breakdowns, shift duties, and on-call assignments when required

Job Opportunity – Electrical Technician We are looking for a qualified Electrical Technician . Key Responsibilities:Perform preventive and corrective maintenance on electrical systems and equipment. Diagnose and repair electrical faults. Install and maintain wiring, electrical panels, and related components. Inspect equipment to ensure safe and efficient operation. Read and interpret electrical drawings and schematics. Follow health and safety procedures. Prepare maintenance and fault reports. Requirements:Diploma in Electrical Engineering, Electrical Technology, or a related field. Relevant experience in electrical maintenance. Good knowledge of electrical panels, wiring, and control systems. Ability to use electrical testing and measuring tools. Strong troubleshooting and problem-solving skills. Ability to work independently and as part of a team. Commitment to safety standards and procedures.

Maintenance and Repair Activities Perform preventive, predictive, corrective, and breakdown maintenance activities on assigned electrical equipment Carry out routine inspections and identify abnormal conditions such as overheating, unusual noise, vibration, oil leakage, loose connections, damaged cables, and insulation deterioration Perform cleaning, tightening, lubrication where applicable, replacement of defective parts, cable termination, minor repair work, and equipment restoration activities Troubleshoot electrical faults, alarms, trips, and abnormal operating conditions to support timely restoration of equipment and minimize plant downtime Ensure maintenance work is completed in accordance with approved procedures, OEM manuals, drawings, safety requirements, and site standards Verify the work area is clean, safe, and properly restored after completion of maintenance activities<br><br>v Support maintenance, inspection, and repair of electrical equipment including, but not limited to:<br><br>Medium-voltage and low-voltage switchgear, circuit breakers, motors repaire, contactors, relays, and control panels Generators, excitation systems, generator auxiliaries, and associated protection systems Generator Circuit Breakers, Isolated Phase Busbars, Gas-Insulated Bus systems, and associated auxiliary equipment where assigned Generator transformers, auxiliary transformers, and transformer auxiliary systems MV and LV motors, motor-operated valves, soft starters, variable frequency drives, and local control stations UPS systems, battery chargers, battery banks, DC distribution boards, emergency lighting, and diesel generator electrical systems Cable systems, cable trays, junction boxes, earthing systems, and lightning protection systems Electrical equipment associated with gas turbines, steam turbines, HRSG systems, water treatment systems, reverse osmosis plants, and balance-of-plant facilities Testing, Inspection, and Troubleshooting Use approved electrical test instruments, including multimeters, clamp meters, insulation resistance testers, continuity testers, earth resistance testers, and phase rotation meters Carry out routine electrical testing such as voltage checks, current checks, insulation resistance testing, battery checks, and earth resistance testing Assist with specialist testing activities such as relay testing, primary injection, secondary injection, breaker timing, contact resistance testing, transformer testing, thermography, and partial discharge testing where applicable Record all test readings accurately and immediately report abnormal results to the Electrical Maintenance Engineer Assist in identifying root causes of equipment failures and support corrective actions as directed Monitor equipment condition and report any developing defects or operational risks Installation, Commissioning, and Modification Support Assist with installation, commissioning, modification, and upgrading of electrical systems and equipment Support equipment testing, energization, functional checks, and return-to-service activities Ensure all installation and modification work complies with technical specifications, approved drawings, and safety requirements Safety, Permit-to-Work, and Compliance Follow all electrical safety rules, permit-to-work requirements, lockout/tagout procedures, grounding requirements, and arc-flash precautions Verify that equipment is properly isolated, discharged, grounded, and tested before work starts Participate in toolbox talks, risk assessments, safety observations, and incident investigations Immediately report unsafe conditions, damaged tools, electrical hazards, near misses, and incidents Ensure all maintenance work is performed in compliance with applicable site procedures, OEM requirements, and environmental, health, and safety standards Documentation and CMMS Support Complete maintenance checklists, inspection sheets, test reports, work completion records, and defect reports accurately Provide clear work feedback to the Electrical Maintenance Engineer, including work completed, materials used, defects found, and follow-up actions required Prepare basic reports on maintenance tasks, equipment condition, and identified issues for review by the Electrical Maintenance Engineer Spare Parts, Tools, and Housekeeping Check the availability of required spare parts, consumables, tools, and test instruments before starting work Handle, store, and preserve electrical spare parts and materials in accordance with site preservation requirements Maintain electrical hand tools, power tools, portable test instruments, and workshop equipment in good working condition Report shortages of spare parts, consumables, and defective tools to the Electrical Maintenance Engineer Support incoming inspection of electrical materials and spare parts in coordination with the Storekeeper when assigned Coordination and Teamwork Work closely with Electrical Maintenance Engineers, Operations personnel, Mechanical and I&C teams, contractors, OEM representatives, and other site personnel Support Operations during equipment isolation, release for maintenance, testing, energization, and return to service Assist in training junior technicians, and new team members in electrical maintenance practices and safety requirements Support continuous improvement by identifying recurring defects, maintenance issues, and opportunities to improve equipment reliability<br><br>Requirements<br><br>Technical Knowledge<br><br>Knowledge of electrical systems used in combined cycle power plants Knowledge of MV and LV switchgear, circuit breakers, transformers, motors, motor control centers, contactors, relays, UPS systems, battery chargers, and DC systems Understanding of generators, generator auxiliaries, power distribution systems, cable systems, earthing systems, and lighting systems Familiarity with electrical drawings, single-line diagrams, wiring diagrams, cable schedules, equipment manuals, and maintenance procedures Understanding of electrical safety requirements, permit-to-work systems, lockout/tagout procedures, grounding, hazardous-energy control, and arc-flash hazards Awareness of electrical protection devices and their functions<br><br>Minimum Qualifications And Experience<br><br>Education<br><br>Electrical Diploma, or an equivalent discipline Electrical trade certification is preferred<br><br>Experience<br><br>Minimum 3 to 5 years of electrical maintenance experience in a power plant, Combined cycle power plant experience is preferred<br><br>Personal Attributes<br><br>Strong commitment to safety, quality, reliability, and compliance Responsible, disciplined, and able to follow instructions and procedures Detail-oriented with a proactive approach to identifying equipment defects Good communication and teamwork skills Ability to work under pressure and manage multiple assigned tasks Willingness to work during planned outages, emergency breakdowns, and on-call duties when required Willingness to work in outdoor and industrial environments<br><br>Physical Requirements<br><br>Physically capable of working in industrial environments Ability to use appropriate personal protective equipment and follow all site safety requirements Ability to respond to emergency maintenance requirements as required

Reab Rehabilitation Center announces a job vacancy for the position of Pharmacist (Male/Female)<br>(Saudi nationals only due to work and regulatory requirements)<br>to work within the medical team, contributing to dispensing medications and monitoring their safe use in accordance with approved regulations and instructions, ensuring quality of care and the safety of beneficiaries.<br>Tasks and Responsibilities:<br>Ability to establish and operate the internal pharmacy, including equipping it, organizing medications, completing regulatory requirements, and coordinating with the relevant authorities to obtain necessary licenses.<br>· Dispense medications to beneficiaries according to approved prescriptions.· Verify the accuracy of dosages and medication instructions before dispensing.· Educate beneficiaries on how to use medications and adhere to the treatment plan.· Monitor the availability of medications and pharmaceutical supplies and coordinate to secure needs.· Store and organize medications according to storage and safety requirements.· Collaborate with physicians and the clinical team to ensure the safe and effective use of medications.· Adhere to professional regulations and instructions and maintain the confidentiality of beneficiary information.<br>Required Qualifications:<br>Saudi National (Male/Female).Bachelor's degree in Pharmacy or Doctor of Pharmacy (PharmD).Valid professional classification and registration from the Saudi Commission for Health Specialties.Experience in the pharmacy field, preferably with previous pharmacy experience.Proficiency in dealing with customers and dispensing medications in accordance with regulations and instructions. Required Skills and Competencies:High accuracy in dispensing medications and reviewing prescriptions.Effective communication skills with beneficiaries and the medical team.Good knowledge of pharmacy regulations and medication safety.Ability to organize inventory and monitor pharmaceutical requirements.Commitment to professional ethics and quality healthcare.<br>Work Location:<br>Residence in the Qassim region<br>

<strong>Role Description</strong> The General Practitioner at Adel Care Medical Group will provide comprehensive primary care services to patients of all ages, including assessment, diagnosis, treatment, and follow-up. Responsibilities include conducting routine and urgent consultations, managing chronic diseases, performing basic clinical procedures, and coordinating care with nursing staff and other healthcare professionals. The role involves maintaining accurate medical records, ordering and interpreting diagnostic tests, prescribing medications, and providing patient education on prevention and health promotion. The General Practitioner will also participate in clinical meetings, contribute to care protocols, and support continuous improvement in service quality. This is a full-time, on-site role based in the Al-Qassim Region.<br><strong>Qualifications<br></strong> <ul><li>Strong clinical foundation with skills in Medicine and Primary Care, providing safe, evidence-based patient management.</li><li>Experience or training in Family Medicine, delivering continuous, holistic care to individuals and families.</li><li>Ability to collaborate effectively with Nursing professionals to ensure coordinated and patient-centered care.</li><li>Demonstrated commitment to Training and ongoing professional development, including participation in clinical education activities.</li><li>Recognized medical degree and valid license to practice as a General Practitioner in the relevant jurisdiction.</li><li>Experience in outpatient or clinic-based primary care settings, preferably within multidisciplinary teams.</li><li>Strong communication and interpersonal skills, with the ability to work respectfully with patients from diverse backgrounds.</li><li>Competence in using electronic medical records and basic digital health tools.</li><li>Ability to manage multiple cases, prioritize workload, and maintain attention to detail in a fast-paced clinical environment.</li><li>Commitment to ethical practice, patient safety, and adherence to local healthcare regulations and guidelines.</li></ul>

Job Purpose : To achieve the sales forecasts and collection of the assigned (General Orthopedic - Trauma) products by prospecting the territory sales opportunities, building up and maintaining relationships with prospects and customers, promoting assigned products, following up orders processes and collection, sustaining customers in-service and reporting on competitors actions.<br><br>Job Responsibilities<br><br>Conduct, document, and communicate analyses and evaluations of customers preferences, business potential and competition actions in his/her territory. Develop the (General Orthopedic - Trauma) products sales forecasts and action plans conforming to the company strategies for his supervisor review and approval. Represent AMICO as authorized partner to sell (General Orthopedic - Trauma) products, by working with a sophisticated audience comprised of surgeons and healthcare professionals. Meet and interact with target customers and key business players defining sales potentials, promoting and selling the assigned products. Participate in the marketing events, conferences, workshops and promotion campaigns relating to his territory and accounts selling assigned products. Support/provide Customers in-service. Ensure skilful technical support to Customers; follow up customer contentment regarding the equipment system installation, start up, utilization, and maintenance. Report on action plans, customers responses, achievements and sales potentials and competitors rivalry. Establish and maintain relationships with clients (surgeons, nursing and clinical staff, etc.). Provide doctor and staff with assistance in the installation and set-up of equipment.<br><br>Candidate Requirements<br><br>Education : Bachelor's Degree in Science / Biomedical Engineer / Pharmacy graduate or any related field from a recognised insititute but not limited to. Experience : 1-3 years experience in similar capacity. Fresher with a flair for selling can also be considered. Competencies / Skills : Good communication skills (Written and Verbal) in English and Arabic. Ability to build relations with persuasive skills. Business acumen with flair for Sales.<br><br>Why Join Us<br><br>At AMICO, we believe in fostering a diverse and inclusive workplace. We recognize the value that different perspectives and experiences bring to our company.<br><br>As part of our commitment to diversity, we encourage applications from all individuals as part of our inclusive hiring practices.<br><br>This initiative is part of our broader diversity agenda aimed at creating a balanced and innovative workforce.<br><br>Skills: sales, medical sales, product specialist, Trauma, orthopedic, Physical therapy

<div dir="rtl"><h3 >نبذة عن الوظيفة</h3> <p >يبحث مجمع نديد الطبي عن <strong >طبيب أسنان عام</strong> للانضمام إلى فريقه في القصيم. يتولى شاغل هذه الوظيفة مسؤولية تشخيص وعلاج أمراض الفم والأسنان المختلفة، وتقديم رعاية صحية شاملة للمرضى. هذه فرصة بدوام كامل تتطلب خبرة تتراوح بين 0-1 سنة.</p> <h3 >الهدف من الدور</h3> <p >يهدف هذا الدور إلى توفير خدمات طب الأسنان الأساسية والمتخصصة للمرضى، بدءاً من التشخيص الدقيق وصولاً إلى تنفيذ الخطط العلاجية ومتابعة الحالات، مع الالتزام بأعلى معايير الجودة والسلامة في الرعاية الصحية ضمن مجمع نديد الطبي.</p> <h3 >المهام والمسؤوليات الرئيسية</h3> <ul > <li >إجراء الفحص السريري لأسنان المريض، وتحديد الصور الشعاعية اللازمة وتحليلها لتشخيص الحالات المرضية للفم والأسنان.</li> <li >إعداد خطط العلاج الشاملة والبرامج الزمنية المناسبة لكل حالة مرضية.</li> <li >تجهيز وتطبيق الحشوات السنية ومعالجة القنوات اللبية للأسنان.</li> <li >تنظيف الأسنان وإزالة الرواسب الكلسية، وتحديد احتياجات المريض من التعويضات السنية.</li> <li >أخذ القياسات اللازمة للتعويضات السنية ومتابعة تنفيذها وتركيبها وضبطها.</li> <li >فحص اللثة وتشخيص أمراضها، ومعالجة التهابات اللثة، وإجراء جراحات الفم الصغرى.</li> <li >وصف العلاجات والأدوية اللازمة للحالات المرضية المختلفة.</li> <li >تطوير أساليب وإجراءات العمل ومواكبة أحدث التطورات في مجال طب الأسنان.</li> <li >إعداد الوثائق والتقارير الطبية المتعلقة بأعمال طب الأسنان وحفظها في قاعدة البيانات الخاصة بها وفقاً للسياسات والإجراءات المنظمة.</li> <li >ضمان تطبيق مبادئ وقواعد السلامة العامة أثناء القيام بجميع أعمال طب وصحة الأسنان.</li> </ul> <h3 >المؤهلات والخبرات المطلوبة</h3> <ul > <li >درجة البكالوريوس في طب الأسنان من جامعة معترف بها.</li> <li >خبرة عملية تتراوح بين <strong >0-1 سنة</strong> في مجال طب الأسنان العام.</li> <li >ترخيص مزاولة المهنة ساري المفعول في المملكة العربية السعودية.</li> <li >القدرة على تشخيص وعلاج مجموعة واسعة من أمراض الفم والأسنان.</li> </ul> <h3 >بيئة العمل ونوع التوظيف</h3> <p >تتمثل بيئة العمل في مجمع نديد الطبي بمدينة <strong >القصيم</strong>. الوظيفة بدوام كامل، وتتطلب الالتزام بتقديم رعاية صحية عالية الجودة ضمن فريق طبي متكامل ومراعاة إجراءات السلامة المهنية.</p> <h3 >للتقديم</h3> <p >ندعو المهتمين ممن تنطبق عليهم المتطلبات المذكورة أعلاه إلى تقديم طلباتهم للانضمام إلى فريقنا في مجمع نديد الطبي.</p></div>

<br><p><strong>Responsibilities</strong></p><p>Diagnose and treat conditions and diseases related to the ear, nose, and throat.</p><p>Perform appropriate clinical examinations, assess patients, and develop suitable treatment plans.</p><p>Follow up with patients and evaluate their response to treatment.</p><p>Manage ENT-related emergencies when required.</p><p>Maintain accurate documentation of patient conditions, diagnoses, and treatment plans.</p><p>Comply with facility policies, procedures, quality standards, and patient safety requirements.</p><p>Collaborate with medical teams and other specialties to ensure comprehensive patient care.</p><p><br></p><p><strong>Qualifications</strong></p><p>Bachelor's degree in Medicine and Surgery from a recognized university.</p><p>Valid professional classification and registration with the Saudi Commission for Health Specialties (SCFHS).</p><p>Relevant clinical experience in ENT.</p><p>Good diagnostic and patient communication skills.</p><p>Ability to work effectively within a team and under pressure.</p><p>Commitment to medical standards, infection control, and patient safety.</p><p>Good command of English; Arabic is preferred.</p>

360 Company Ltd. is a growing automotive service company in Saudi Arabia, providing professional mechanical, electrical, diagnostic, air-conditioning, engine, transmission, and general vehicle maintenance services and spare parts. We are committed to delivering high-quality workmanship, trusted customer service, and modern automotive solutions. We are looking for a motivated and sales-oriented Automotive Service Advisor to join our Riyadh | Khobar | Buraidah | Unaizha branches. The successful candidate will communicate with customers, understand their vehicle concerns, recommend suitable services, prepare service estimates, coordinate with the workshop team, and ensure an excellent customer experience.<br>Requirements Strong knowledge of automotive maintenance and repair services Good understanding of automotive workshop processes Excellent sales, communication, and customer service skills Ability to explain technical issues and service recommendations clearly Minimum 1 year of relevant experience Proficiency in Arabic with good English communication skills Ability to achieve sales targets and handle customers professionally<br>What We Offer Competitive, industry-standard salary based on experience Iqama and medical insurance as per company policy Attractive sales incentives and performance rewards Advanced technical, sales, and customer service training Clear career development and promotion opportunities Professional and supportive working environment<br>Ready to grow your automotive career with 360 Company Ltd.?<br>Apply now and become part of a fast-growing team where your skills, performance, and ambition are recognised and rewarded.

We are looking for an experienced Workshop & Fleet Maintenance Supervisor to join our Facility Management team. The ideal candidate should be a strong hands-on technician with solid experience in vehicle maintenance and repair, as well as the ability to supervise technicians, manage workshop activities, and ensure the operational readiness of the company’s fleet and equipment. Job Summary The Workshop & Fleet Maintenance Supervisor will be responsible for supervising daily workshop and fleet maintenance operations, diagnosing technical faults, following up on mechanical and electrical repairs, supervising technicians, and ensuring that vehicles and equipment are safe, reliable, and ready for operation. Key Responsibilities Supervise daily workshop operations and maintenance activities. Diagnose vehicle and equipment faults and provide technical guidance to technicians. Participate in troubleshooting and repair activities when required. Supervise, distribute, and follow up on technicians’ daily tasks. Follow up on preventive and corrective maintenance schedules. Inspect completed repairs and ensure proper repair quality before releasing vehicles/equipment. Manage vehicle breakdowns and emergency repair requirements. Ensure the operational readiness, safety, and reliability of fleet and equipment. Coordinate with fleet/transport operations to minimize vehicle downtime. Monitor spare parts, tools, workshop equipment, and consumables. Maintain accurate maintenance records, repair history, and vehicle technical files. Monitor maintenance costs and spare parts consumption. Follow up on vehicle inspections, licensing, accidents, and related technical procedures. Ensure compliance with company HSE procedures and applicable Saudi regulations. Prepare daily, weekly, and monthly maintenance and technical reports.???? Qualifications Diploma or Bachelor’s degree in Automotive Technology, Mechanical Engineering, Mechanical Technology, or a related technical field. Strong practical knowledge of vehicle mechanical and electrical systems. Technical certifications in vehicle maintenance, diagnostics, or fleet maintenance are preferred.???? Experience & Skills Minimum 5 years of relevant experience in vehicle maintenance, workshop operations, fleet maintenance, or a similar role. Strong hands-on experience in diagnosing and repairing mechanical and electrical vehicle faults. Proven experience supervising automotive technicians and workshop teams. Strong knowledge of preventive and corrective maintenance. Ability to inspect vehicles, identify faults, and verify completed repairs. Experience in fleet operations and vehicle breakdown management. Good knowledge of spare parts, workshop tools, and maintenance procedures. Experience with GPS tracking and fleet management systems. Experience dealing with Saudi systems and authorities such as TAMM, Najm, and Traffic systems is preferred. Good reporting, communication, and team leadership skills. Ability to work under pressure and respond to emergency breakdowns.

<p><strong>Job Title: Dentist</strong></p><p><strong>Department: Dental Services</strong></p><p><strong>Reports To: Medical Director</strong></p><p><br></p><p><strong>Job Summary</strong></p><p>The Dentist is responsible for diagnosing, treating, and preventing dental and oral health conditions while providing safe and high-quality patient care. The role delivers appropriate dental treatments, develops individualized care plans, and promotes preventive oral healthcare in accordance with clinical standards and organizational policies.</p><p><br></p><p><strong>Key Responsibilities</strong></p><ul><li>Examine, diagnose, and treat patients with dental and oral health conditions</li><li>Perform dental procedures, including preventive, restorative, and minor surgical treatments within the approved scope of practice</li><li>Develop individualized treatment plans and educate patients on oral hygiene, preventive care, and treatment options</li><li>Maintain accurate and timely patient records, clinical documentation, and treatment information</li><li>Comply with infection prevention standards, patient safety requirements, clinical guidelines, and organizational policies</li></ul><p><br></p><p><strong>Qualifications</strong></p><ul><li>Bachelor's degree in Dentistry (BDS, DDS, DMD, or equivalent)</li><li>Valid SCFHS professional classification and registration</li><li>Minimum 1 years of relevant clinical experience as a Dentist</li></ul><p><br></p>

<h3 >About XPL Solutions</h3> <p >XPL Solutions is a prominent local leader in Saudi Arabia, specializing in providing cutting-edge logistics solutions for both multinational and local companies. The company played a significant role during the Covid19 crisis, demonstrating its capability to find fast and adaptive solutions to react effectively to the challenges faced in the Kingdom.</p> <h3 >The Role: Inventory Supervisor</h3> <p >XPL Solutions is seeking a <strong >Full-time Inventory Supervisor</strong> to join its operations in <strong >Al Qassim</strong>. This role is crucial for leading and managing the end-to-end inventory within a medical warehouse. The supervisor will ensure that physical stock aligns precisely with client systems, specifically NUPCO, and will oversee all aspects of stock movement, including receiving, issuing, and destruction processes, alongside managing daily cycle stock count activities.</p> <h3 >Key Responsibilities</h3> <ul > <li >Follow and execute the Cycle Count Stock checking plan (monthly, weekly, daily).</li> <li >Conduct daily checks of receiving and consumption stock.</li> <li >Perform physical item checks to ensure actual stock matches system reports.</li> <li >Issue Physical Stock reports to relevant inventory officers.</li> <li >Identify and investigate variations in stock quantity between physical stock and system records.</li> <li >Ensure batch-managed items have accurate expiry dates recorded in the system.</li> <li >Collaborate with the operation manager and client representative to resolve and finalize stock quantity variations.</li> <li >Issue Variation Stock reports and track adjustments on the client system.</li> <li >Validate non-moving stock and create a catalogue for it when requested.</li> <li >Identify and install pin locations within the warehouse racking system.</li> <li >Maintain and monitor warehouse processes in accordance with quality and WMS system requirements.</li> <li >Validate expiry stock and instruct the warehouse team to shift expired goods to the designated expiry area.</li> <li >Supervise the destruction process of expired stock.</li> <li >Adhere to client Standard Operating Procedures (SOPs) and operational procedures.</li> <li >Manage various inventory activities, including Cycle Count Procedure, Goods Returned Procedure, Recall procedure, handling of counterfeit products, Traceability procedure, Preservation Procedure, and Quarantine.</li> </ul> <h3 >Required Experience and Qualifications</h3> <p >Candidates should possess <strong >5-10 years of experience</strong> in inventory management or a related field. A comprehensive understanding of Supply Chain principles and exposure to ERP and other world-class forecasting and planning tools are essential. Familiarity with medical items and NUPCO procedures in warehouse operations is also required.</p> <h3 >Essential Skills and Attributes</h3> <ul > <li >Hardworking, intelligent, and highly detail-oriented with a strong analytical mind.</li> <li >Ability to multi-task effectively and work independently in a fast-paced environment.</li> <li >Proven leadership abilities, demonstrating the capacity to lead by example.</li> <li >Capable of accepting constructive criticism and dealing calmly and effectively within high-stress situations.</li> <li >Ability to create an environment where company values are a strong and living reality that embraces the diversity of employees and visitors.</li> </ul> <h3 >Application Information</h3> <p >We invite qualified candidates who meet the specified requirements to apply for this full-time position. Further details regarding the application process will be provided upon interest.</p>

<p>Overview</p><p>We are seeking a competent engineer to join our technical team specializing in concrete quality management and control. You will play a pivotal role in ensuring that all construction products and processes comply with technical standards as well as Saudi and international specifications by directly supervising laboratory tests and analyzing results with high precision.</p><p>Responsibilities and Duties</p><ul><li>Conduct necessary laboratory and field tests for concrete and raw materials (aggregate, cement, admixtures) in accordance with standard specifications.</li><li>Analyze test results and issue accurate, approved technical reports.</li><li>Supervise quality control on production lines or at project sites to ensure concrete mixes meet the required specifications.</li><li>Monitor the periodic calibration of laboratory equipment to ensure the accuracy of results and the integrity of equipment.</li><li>Communicate with site engineers to provide technical advice and resolve issues related to concrete manufacturing or pouring.</li><li>Implement occupational health and safety procedures within the laboratory and work environment.</li></ul><p>Qualifications and Requirements</p><ul><li>University degree in Civil Engineering or equivalent.</li><li>Proven practical experience in managing concrete laboratories ranging from 5 to 8 years.</li><li>Full knowledge of the Saudi Building Code (SBC) as well as American (ASTM) and British (BS) standards.</li><li>High ability to prepare and write technical reports in both Arabic and English.</li></ul><p>Required Skills</p><ul><li>Precise analytical skills and the ability to derive engineering solutions.</li><li>Proficiency in computer software and statistical data analysis applications.</li><li>Effective communication skills to work within multidisciplinary teams.</li><li>Ability to make decisions under work pressure.</li></ul><p>Benefits and Perks</p><ul><li>Competitive salaries commensurate with experience and qualifications.</li><li>A professional work environment that encourages professional growth.</li><li>Provision of comprehensive medical insurance and coverage for social benefits in accordance with the Saudi Labor Law.</li><li>Opportunities for continuous training and development in material testing technologies.</li></ul>

<ul><li>Diagnose and repair complex turbocharger systems, identifying root causes of performance issues and mechanical failures.</li><li>Perform precise disassembly, cleaning, inspection, and reassembly of turbocharger components, adhering to strict tolerances.</li><li>Conduct dynamic balancing and alignment of rotating turbocharger assemblies to ensure optimal performance and longevity.</li><li>Install and commission new or rebuilt turbochargers, ensuring proper integration with engine systems and exhaust configurations.</li></ul><p><strong>Desired Candidate Profile</strong></p><ul><li>Possess a technical degree or vocational certification in Automotive Technology, Mechanical Engineering, or a related field.</li><li>Hold certifications such as ASE L3 Light Duty Hybrid/Electric Specialist or equivalent specialized turbocharger training.</li><li>Have a minimum of 5 years of hands-on experience specifically with turbocharger diagnostics, repair, and rebuilding.</li><li>Demonstrate a strong understanding of internal combustion engines, exhaust systems, and related pneumatic/hydraulic controls.</li></ul>

Job Title: Legal Advisor Department: Legal Affairs Reports To: Legal Manager<br>Job Summary The Legal Advisor is responsible for providing legal advice and guidance to the organization on corporate, commercial, employment, and regulatory matters. The role supports the review of legal documents, ensures compliance with applicable laws and regulations, minimizes legal risks, and protects the organization's legal interests.<br>Key Responsibilities Provide legal advice and guidance to management and departments on corporate, commercial, employment, and regulatory matters Review, draft, and negotiate contracts, agreements, policies, and other legal documents Monitor compliance with applicable laws, regulations, and organizational policies, and recommend corrective actions where required Support the management of legal claims, disputes, investigations, and litigation by coordinating with external legal counsel when necessary<br>Qualifications Bachelor's degree in Law or a related legal field Healthcare or hospital experience is preferred Strong knowledge of Saudi laws, corporate governance, contract law, labor law, and regulatory compliance Fluency in Arabic and English languages

Job Summary We are looking for an experienced Fleet & Workshop Supervisor to oversee daily fleet and transportation operations, supervise drivers and technicians, and ensure the availability, safety, and operational readiness of vehicles and equipment. Key Responsibilities Supervise daily transportation operations and driver activities. Manage vehicle and equipment movements and daily routes. Monitor vehicle cleanliness, safety, inspections, licenses, and operational readiness. Follow up on preventive and corrective maintenance activities. Coordinate with the workshop for vehicle repairs and maintenance schedules. Monitor fuel consumption, mileage, GPS tracking, and fleet operating costs. Supervise workshop activities, spare parts, tools, and consumables. Prepare operational and technical reports and maintain vehicle records. Ensure compliance with company safety procedures and applicable Saudi regulations. Follow up on vehicle accidents, traffic violations, and related procedures. Qualifications Diploma or Bachelor’s degree in Transportation, Mechanical Engineering, Industrial Engineering, or a related field. Professional courses in Fleet Management, Vehicle Maintenance, or Occupational Safety are preferred. Experience & Skills Minimum 5 years of relevant experience in fleet/transport operations, driver supervision, vehicle maintenance, and workshop management. Experience dealing with Saudi systems and authorities such as TAMM, Najm, and Traffic systems. Good knowledge of preventive vehicle maintenance and fleet operations. Experience using GPS tracking systems. Ability to prepare operational and technical reports and daily operating schedules. Strong knowledge of safety procedures and emergency management.

ACWA Operations:At Acwa Operations, we make essential services dependable and efficient for the millions of people who rely on them every day. Formerly NOMAC (The First National Operations & Maintenance Company), we are the operations and maintenance arm of Acwa, focused on keeping power generation and water desalination assets running safely, reliably and cost-effectively across their full lifecycle. Since 2005, we have partnered with clients across the Middle East, Africa and Asia to support complex infrastructure that powers communities and sustains economies. As part of Acwa, we bring deep technical knowledge, strong operational systems and a culture built on performance and accountability. Our work covers everything from commissioning and asset management to preventive and corrective maintenance, technical support and continuous performance improvement. We know that reliability and cost discipline aren’t just technical goals, they determine whether people have light at night, water in their homes and industry can operate without interruption. By maximising asset availability, enhancing resilience and upholding the highest safety and quality standards, Acwa Operations contributes directly to Acwa’s mission to deliver sustainable, affordable energy and water solutions that advance people’s lives and strengthen communities worldwide.<br>Qassim 1 Independent Power Project with a capacity of 1,800 MW is a Combined Cycle Gas Turbine IPP that is developed by ACWA Power in Al-Qassim region of Saudi Arabia. ACWA Power and the Saudi Power Procurement Company (SPPC) have signed a 25-year Power Purchase Agreement (PPA) for the Development, Financing, Build, Own and Operate of a 1,800 MW Combined Cycle Gas Turbine plant. Saudi Power Procurement Company acting as the sole off-taker for this project. In addition to ACWA Power, the shareholders include the Saudi Electricity Company (SEC), which holds a 40% share, and Haji Abdullah Alireza & Co. LTD (HAACO), which holds a 20% share.<br>REPORTS TO: Plant General Manager<br>JOB PURPOSE:Maintenance Manager being Head of maintenance organization structure is responsible for the efficient and reliable maintenance of the plant ensuring all safety regulation, maintenance procedures and company polices are followed.<br>KEY ACCOUNTABILITIES:Strategy & Plans:Develop the Maintenance-departmental strategy in line with the Plant’s strategy to ensure vertical alignment and horizontal integration with other interfacing departmental strategies across. Regularly report to the Plant General Manager on the operational activities of department, challenges and issues faced, mitigations taken, etc. as required, to keep them informed and updated on the division’s activities. Budget Management:Contribute to the preparation of the Maintenance department’s budget and manage and monitor the financial performance against the budget so that areas of unsatisfactory performance are identified, rectified promptly and potential performance improvement opportunities are capitalised upon. Maintenance Planning:Lead and manage the planning of preventive, corrective and condition-based maintenance plans / work schedules (including annual and long-term maintenance plans) for all types of maintenance (Electrical, Mechanical and I&C) across the facilities in the plant ensuring that maintenance jobs are carried out timely, efficiently and cost effective with adherence to HSE standards. Lead the effective cascading of the maintenance strategy into work instructions and SOPs for each equipment and process in all areas of mechanical, electrical, instrumental, controls and systems and ensure their implementation by employees and contract staff, to ensure safe and timely maintenance of equipment. Maintenance Management:Lead the effective implementation of approved plans in liaison with the discipline engineers and operations team across all the assets and equipment within set timelines and budget to facilitate uninterrupted operations. Oversee the equipment risk assessment process in order to facilitate proactive identification of anomalies and ensure optimum risk mitigation in accordance with best practices. Manage the timely response to all emergency breakdowns and provide prompt corrective action to ensure plant availability, thereby minimizing downtime and possibility of liquidity damages. Oversee the maintenance documentation process in SAP ensuring it is completed correctly including filling in the log, outlining the fault, method of repair and the time, labour and materials used to support timely availability of information. Review the daily maintenance / condition monitoring reports and submit periodic reports to the management, keeping them informed of all technical problems, if any, as well as recent changes or modifications on existing work plant or schedule. Lead the Maintenance management meetings so that the entire team is clear on the standards required and the maintenance programs that are underway. In the Project Phase: Coordinate with the EPC representatives on site to understand the critical equipment installation etc., and undertake the Commissioning Monitoring, Acceptance Test Campaign and “As-build” documentation activities, to ensure required transfer of knowledge. Outage Management:Together with the Planning Engineer, lead the effective forecasting of manpower and material requirements to ensure timely availability of resources and spares for effective execution of maintenance plans. Lead the planning and execution of the annual outage maintenance of critical equipment, as per the recommendation of the OEM, and provide technical guidance and support to ensure the EHS, scope, cost, and timeline objectives are met. Technical Guidance:Act as a technical expert to ensure that all modifications to the maintenance procedures and work instructions are correctly designed and implemented as per the recommendations of the OEMs in order to best optimize maintenance operations according to the availability of equipment and workforce. Lead the development of a condition based preventive maintenance culture on day-to-day basis by conducting troubleshooting and root cause analyses, finding solutions to reduce reactive maintenance. Manage and provide short- and long-term technical solutions to engineering problems that may arise in relation to maintenance services in order to proactively resolve such problems on a sustainable basis and ensure uninterrupted delivery of services. Health, Safety, Security & Environment:Ensure compliance to all relevant health, safety, security and environmental management policies, procedures and controls across the department to guarantee employee safety, legislative compliance and a responsible environmental attitude. Report and respond to HSSE incidents using the established emergency communication channels and protocols, to minimise the impact of the hazard. Together with HSE department, ensure that safety rules and regulations are fully explained to plant employees / contractor staff and appropriate safety and protective equipment is worn; safety notices are prominently displayed in all work areas and that all accidents and incidents are efficiently investigated and analysed whilst ensuring that measures are implemented to avoid any recurrence. Continuous Improvement:Identify opportunities of improvement and contribute to Maintenance department change initiatives, programmes and projects taking into account best practice and standards in the business environment. People Management:Manage the effective achievement of the team’s objectives through setting individual objectives, managing performance, developing the team and providing formal and informal feedback to maximise overall performance, engagement and motivation.<br>REQUIRED WORK EXPERIENCE AND EDUCATION: A Bachelor degree holder in Mechanical / Electrical Engineering.20 years of experience in a similar environment with few years in a managerial position preferably within the Power / Water generation sector. Experience developing / implementing preventive and predictive maintenance processes is highly desirable.<br>REQUIRED SKILLS AND KNOWLEDGE:In-depth knowledge of downtime analysis and knowledge of problem-solving tools In-depth Knowledge of maintenance management methods, of predictive inspection tools and of CMMS (Computer Maintenance Management System, good knowledge of SAP Template desirable) Detailed understanding of preventative/predictive maintenance theory Strong mentoring, coaching and people management skills In-depth knowledge of the operations in water desalination and power generation plants and of ACWA NOMAC operations Strong planning, organizing, and integration skills Team work and effective collaboration skills Good understanding of PPPs, contractual obligations etc.

Maintenance Planning & Execution: Develop and implement inspection, maintenance, and repair schedules for all mechanical systems and equipment, including gas turbines, steam turbines, generators , condenser, heat recovery steam generators (HRSG), pumps, compressors, HVAC and other ancillary systems Ensures necessary tooling Ensures necessary Third-Party Certification Team Leadership: Lead, mentor, and supervise a team of mechanical maintenance engineers and technicians to ensure efficient maintenance operations and achieve targets & objectives Foster a culture of safety, compliance, and continuous improvement among team members Technical Support: Provide technical guidance and support to maintenance staff for troubleshooting and problem resolution of mechanical issues Provide in housetraining to enhance the team skills technically & safety Conduct root cause analysis of mechanical failures and implement corrective measures Project Management: Plan and oversee mechanical maintenance projects, ensuring they are completed on time and within budget Coordinate with other departments (operations, electrical, and instrumentation) to schedule maintenance work with minimal disruption to plant operations Budget and Resource Management: Assist the Maintenance Manager in the preparation of the annual maintenance budget and manage resource allocation effectively Monitor maintenance costs and identify opportunities for cost reductions without compromising safety or reliability<br><br>6 . Procurement & Storage<br><br> Ensures adequate inventories of spares and consumables and ensure timely procurement for the efficient operation To prepare purchase requisitions for spare parts and consumables<br><br>To perform technical evaluation of quotations received from purchase department and recommend appropriate choice.<br><br> Compliance and Safety: Ensure compliance with environmental regulations, safety standards, and industry best practices Conduct regular safety audits, risk assessments, and initiate safety improvement programs Ensure compliance of Corporate and site specific procedures and Work Instructions Documentation and Reporting: Maintain accurate records of maintenance activities, equipment performance, and inventory Prepare detailed reports on maintenance work, performance metrics, and project status for management review KPIs development, implementation and tracking, Continuous Improvement: Identify and implement improvement initiatives in mechanical maintenance processes and workflows Stay abreast with industry trends, advancements in technology, and maintenance best practices<br><br>10 Pre-PCOD role<br><br> support the Owner during the design review phase and during installation, commissioning, testing, and trial operation period O & M manuals and Initial Spare Parts list Review and finalization Development of Master Equipment List Development and implementation of CMMS Spares and maintenance strategy identification based on Criticality study of equipment Prepare site specific maintenance procedures and Work Instructions Ensure Maintenance team authorization as Permit Receivers Ensure timely placement of subcontracts ensure readiness for the operational period, by ensuring that all staff are trained and that all the systems and process required for O&M operations are ready ensure that the plant is fit for purpose to be taken-over and the plant is designed, built, commissioned and tested as per the EPC Contract and other Project Agreements<br><br>Requirements<br><br>Education: Bachelor's degree in Mechanical Engineering or a related field<br><br>Experience: Minimum of 10 years of relevant experience in mechanical maintenance, in large scale combined cycle power Plant. IPP and Siemens GT experience is preferred.<br><br>Leadership Skills: Proven experience leading maintenance teams, with strong interpersonal and communication skills.<br><br>Technical Skills: Proficiency in mechanical maintenance systems, reliability engineering, and condition monitoring techniques.<br><br>Software Knowledge: Familiarity with maintenance management software (CMMS) and Microsoft Office Suite.

QHSE Officer – Facilities Management O&M, maintenance, or large-scale site operations. The role requires someone who can maintain high safety, quality, and compliance standards across active project environments. Employment Type: Full-time Work Arrangement: On-site<br><br>Candidate Requirement: Saudi nationals are encouraged to apply in line with Saudization and project localization requirement<br>s<br>Role Purpose.se The QHSE Officer will support the implementation, monitoring, and continuous improvement of Quality, Health, Safety, and Environment standards across FM operations. The role will ensure site compliance, conduct inspections, support audits, report incidents, follow up corrective actions, and work closely with project teams to maintain safe and compliant operati<br>on<br>Key Responsibilit Conduct regular QHSE inspections, site walks, audits, and compliance assessments across FM project sites. Monitor and verify the implementation of HSE policies, procedures, permits, risk assessments, and method statements. Identify unsafe acts, unsafe conditions, quality deficiencies, and non-compliance issues, and follow up on corrective and preventive actions until closure. Support investigations of incidents, accidents, near misses, and non-conformities, and prepare clear and accurate reports. Maintain QHSE documentation, inspection records, audit reports, training records, and compliance tracking systems. Facilitate toolbox talks, safety briefings, awareness campaigns, and site-level QHSE training sessions. Coordinate with operations teams, maintenance personnel, supervisors, subcontractors, and client representatives on all QHSE-related matters. Ensure compliance with applicable Saudi regulations, company standards, client requirements, and project-specific QHSE procedures. Monitor PPE compliance, work-at-height activities, electrical safety practices, housekeeping standards, waste management processes, emergency preparedness, and permit-to-work controls. Support internal and external audits and assist in closing audit findings within agreed timelines. Promote a proactive safety culture and maintain high standards of QHSE discipline across all site teams. Provide regular QHSE performance updates and recommendations to management to support continuous improvement initiativ<br>es.<br>Required Diploma or Bachelor's Degree in Occupational Health & Safety, Engineering, Environmental Science, Quality Management, or a related field. Minimum 3 years of experience in QHSE/HSE roles. Previous experience in Facilities Management (FM), Integrated Facilities Management (IFM), Operations & Maintenance (O&M), maintenance services, building services, or large operational project environments is required. Good knowledge of:Site safety practices Risk assessments Incident and accident reporting Audits and inspections Corrective and preventive action follow-up Corrective and preventive action follow-up Professional certifications such as NEBOSH, IOSH, OSHA, ISO 45001, ISO 9001, or ISO 14001 are preferred. Strong communication and interpersonal skills with the ability to work effectively with project teams, supervisors, technicians, subcontractors, and client representatives. Proficient in Microsoft Office applications and report preparation. Willingness and ability to work on-site and travel or relocate to project locations across Saudi Arabia as requi<br>red.<br>Preferred Strong background in Facilities Management (FM) and Operations & Maintenance (O&amp;M) environments. Confident in interacting with site teams and addressing operational challenges. Able to work independently with minimal supervision. Detail-oriented, disciplined, and committed to maintaining high QHSE standards. Strong follow-up and coordination skills with the ability to ensure timely closure of corrective and preventive actions. Proactive approach to promoting a positive safety culture and continuous improvement across project s<br>ites.